The Kernel config option CONFIG_DRM_DISPLAY_HELPER has no title and can
not be directly selected. Do the same for this kmod and make it hidden.
Link: https://github.com/openwrt/openwrt/pull/19480
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
075cdc0 iptime-crc32: add support for ipTIME AX3000Q
48ababa iptime-crc32: add support for ipTIME AX3000SM
f29de74 iptime-crc32: Add device support for ipTIME AX6000M
Link: https://github.com/openwrt/openwrt/pull/19520
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
On some devices (like ZyXEL GS1920) the phys are not initialized and patched
by the bootloader. This is done through the vendor SDK when the software
starts. To make these devices usable too, provide the most basic setup
sequence for the RTL8218B.
Signed-off-by: Markus Stockhausen <markus.stockhausen@gmx.de>
Link: https://github.com/openwrt/openwrt/pull/19491
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
The driver currently uses two checks to verify the capabilities. These
are ..._phylink_get_caps() and ..._pcs_validate(). For RTL930x these
must allow 2.5G modes. Enhance that as follows:
Add 2500BASEX to phylink_get_caps(). Sort the interfaces alphabetically
and rename the function to the new prefix. IMPORTANT REMARK! Until now
this function allowed the XGMII mode (10G only parallel interface) that
was somehow mixed with the Realtek proprietary mode XSGMII (10G SGMII).
Remove it to avoid further confusion.
Looking upstream pcs_validate() is used less and less. There are only
2 consumers left in 6.16 and the calling location reads:
/* Validate the link parameters with the PCS */
if (pcs->ops->pcs_validate) {
ret = pcs->ops->pcs_validate(pcs, supported, state);
if (ret < 0 || phylink_is_empty_linkmode(supported))
return -EINVAL;
/* Ensure the advertising mask is a subset of the
* supported mask.
*/
linkmode_and(state->advertising, state->advertising,
supported);
}
There is no need for this additional check. Drop the functions.
Tested-by: Jan Hoffmann <jan@3e8.eu>
Signed-off-by: Markus Stockhausen <markus.stockhausen@gmx.de>
Link: https://github.com/openwrt/openwrt/pull/19429
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Fallback to default mbedtls configurations in case of the package is
not configured. It is possible for some reasons it get built even if
it's unselected because of build system bugs or other build-only
dependencies. In this case current behavior will comment out all
necessary configurations and lead build errors.
Fixes: 5359639c2b ("mbedtls: Apply configuration in Configure instead of Prepare")
Signed-off-by: Tianling Shen <cnsztl@immortalwrt.org>
Link: https://github.com/openwrt/openwrt/pull/19495
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
5d10084ea885 lib-ucode.c: add #define _GNU_SOURCE
a95364b41d52 udebug-cli: fix terminating uloop
c00eb9b685a8 ucode: use FILE handle for pcap output
4265167cb6e8 ucode: add error reporting to pcap_write
4a908ee731a6 udebug-cli: stop event loop on write failure
6e04f4187231 ucode: use ucv_resource_create_ex for remote rings
c297f04e1852 ucode: drop use ucv_resource_create
f207d37a1055 ucode: add support for specifying ring format
98683a94bcdd ucode: support appending array data, similar to socket.send()
a7ecd483ed38 ucode: allow calling udebug.init() multiple times
d4a4c788c416 ucode: fix allocation size of local ring meta
184706abaf50 ucode: add timestamp argument to foreach()
8442c948c193 ucode: add function for getting ring information
f4958a4c591a ucode: add const entries for enum udebug_format
14d4fec36993 udebug-cli: add logstream command
6ed8536142bb ucode: fix entries/size confusion
Signed-off-by: Felix Fietkau <nbd@nbd.name>
The PHY LED is connected to EN8811H's internal GPIO, which is unable
to be controlled by current driver.
Signed-off-by: Tianling Shen <cnsztl@immortalwrt.org>
These instructions are for 64-bit load/store. On ARMv5TE, the CPU
requires addresses to be aligned to 64-bit. When misaligned, behavior is
undefined (effectively either loads the same word twice on LDRD, or
corrupts surrounding memory on STRD).
On ARMv6 and newer, unaligned access is safe.
Removing these instructions for ARMv5TE is necessary, because GCC
ignores alignment information in pointers and does unsafe optimizations
that have shown up as bugs in various places.
This patch was originally added more than 11 years ago in commit b050f87d13,
but got lost 6 years ago, when gcc 9.1 was added in 88c07c6552.
This primarily affects the kirkwood and ixp4xx targets
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Fix bootloop on TP-Link EAP615-Wall v1 by reducing LZMA dictionary
size. Before this patch and after an upgrade to kernel 6.12 this
device couldn't boot a kernel because of an error: "lzma compressed:
uncompress error 1".
I have chosen -d22 as dictionary size as suggested by @namiltd.
The usual sizes for problematic devices are -d16, -d20, -d22. I
have confirmed with my tests that this device can boot with a value
up to -d27, but there is no size benefit from values above -d21,
therefore -d22 is good enough.
See also: https://github.com/openwrt/openwrt/issues/19403
Signed-off-by: Marcin FM <marcin@ipv8.pl>
Link: https://github.com/openwrt/openwrt/pull/19433
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Specification
-------------
- SoC : MediaTek MT7981BA dual-core ARM Cortex-A53 1.3GHz
- RAM : DDR3 256Mbytes, ESMT M15T2G16128A
- Flash : 128Mbytes NAND Flash, ESMT F50L1G41LB
- WLAN : MediaTek MT7976CN dual-band Wi-Fi 6
- 2.4GHz : b/g/n/ax, MU-MIMO
- 5GHz : a/n/ac/ax, MU-MIMO
- Ethernet : MediaTek MT7531AE
- LAN : 10/100/1000 Mbps x4
- WAN : 10/100/1000 Mbps x1
- UART : 1x4 pin header on PCB
- [J6] TX, RX, GND, 3.3V (115200, 8N1)
- Buttons : WPS, Reset
- LEDs : 1x CPU (Amber)
1x Wi-Fi 5GHz (Amber)
1x Wi-Fi 2.4GHz (Amber)
1x WAN activity (Amber)
4x LAN activity (Amber)
- Power : 12VDC, 1A (Center positive polarity)
MAC address
-----------
+-----------+-------------------+-----------------------+
| Interface | MAC | Algorithm |
+-----------+-------------------+-----------------------+
| WLAN 2.4G | B0:38:6C:48:xx:xx | label |
| WLAN 5G | B2:38:6C:48:xx:xx | label with LA Bit Set |
| WAN | B0:38:6C:48:xx:xx | label + 1 |
| LAN | B0:38:6C:48:xx:xx | label + 3 |
+-----------+-------------------+-----------------------+
The WLAN 2.4G MAC was found in 'Factory' partition, 0x4
Installation
------------
1. Download the OEM recovery software from the manufacturer's website
2. Download the *squashfs-factory.bin file from the OpenWrt website
3. Press a reset button, and power up the router(keep pressing the reset button)
4. Wait more than 10 seconds until the CPU LED stop blinking
5. Connect the router(LAN port) to the PC
6. Replace a file in the OEM recovery software with the file from step 2
7. Run the OEM recovery software and follow the instructions
8. Wait for the router to boot from *squashfs-factory.bin
Signed-off-by: Donghyun Ko <nyankosoftware@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/19368
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Some NanoPC-T6 boards with A3A444 eMMC chips experience I/O errors and
corruption when using HS400 mode. Downgrade to HS200 mode to ensure
stable operation.
Fixes: #18844
Signed-off-by: Grzegorz Sterniczuk <grzegorz@sternicz.uk>
Link: https://github.com/openwrt/openwrt/pull/19398
[Add patch header]
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
6953f19 wireless-regdb: Update regulatory info for Indonesia (ID) for 2025
2e8214e wireless-regdb: Permit 320 MHz bandwidth in 6 GHz band for GB
a94f685 wireless-regdb: Update regulatory info for Egypt (EG) for 2024
7628ce2 wireless-regdb: Update regulatory rules for Brazil (BR) on 6GHz
4411b39 wireless-regdb: Update regulatory info for Vietnam (VN) for 2025
490f136 wireless-regdb: Update regulatory info for Estonia (EE) for 2024
c56c663 wireless-regdb: update regulatory rules for Paraguay (PY) on 6 GHz for 2025
5a8ced5 wireless-regdb: Update regulatory info for CEPT countries for 6GHz listed by WiFi Alliance
5fd8ee3 wireless-regdb: update regulatory rules for Bosnia and Herzegovina (BA) for 6 GHz
e05260a wireless-regdb: update regulatory database based on preceding changes
Link: https://github.com/openwrt/openwrt/pull/19474
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
This commit increases the SPI bus frequency from 20 to 52 MHz. Reduces boot
time by 2s. Below is a performance comparison.
Before:
root@OpenWrt:~# dd if=/dev/mtd5 of=/dev/null bs=10M count=1 status=progress
10485760 bytes (10 MB, 10 MiB) copied, 2 s, 5.8 MB/
After:
root@OpenWrt:~# dd if=/dev/mtd5 of=/dev/null bs=10M count=1 status=progress
10485760 bytes (10 MB, 10 MiB) copied, 1 s, 9.7 MB/s
Taken from PR #18752 as each device should be tested individually, so I have
created a separate PR for this.
Signed-off-by: Sky Huang <SkyLake.Huang@mediatek.com>
Signed-off-by: Aleksander Jan Bajkowski <olek2@wp.pl>
Link: https://github.com/openwrt/openwrt/pull/19439
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
There is some confusion in the Git log of this file. Specifically,
the commit message on 7b7f1702 incorrectly indicates that there was
"potential fear" about copyright infringement.
Upon review of this situation, there is, in my opinion, no concern of
copyright infringement here. This is not legal advice; it is my
opinion based of years of work on copyright policy for FOSS.
However, Elliott Mitchell's idea was obviously helpful as inspiration
in writing this script and deserves credit. Ideas alone, however,
are not to my knowledge copyrightable anywhere in the world.
Signed-off-by: Bradley M. Kuhn <bkuhn@sfconservancy.org>
With the switch to Linux 6.12 this driver was enabled by accident.
However, it doesn't support any of the router SoCs but is meant to be
used only by the smartphone, tablet and chromebook SoCs.
Disable the driver again to silence a kernel error logline during boot.
Fixes: 0a0f5f94ec ("mediatek: mt7623: update config-6.12")
Fixes: 029b7ed9c4 ("mediatek: mt7622: update config-6.12")
Reported-by: https://aparcar.org/openwrt-tests/119/
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
