Currently, OpenSBI reserves the upper 16 bits in mhpmevent for
the Sscofpmf extension.
However, according to the Sscofpmf extension specification [1],
it only defines the upper 6 bits in mhpmevent for privilege mode
inhibit and counter overflow disable. Other bits are defined by
the platform for event selection.
Since vendors might define raw event encoding exceeding 48 bits in
mhpmevent, we should adjust the MHPMEVENT_SSCOF_MASK to support it.
Link: https://github.com/riscv/riscv-isa-manual [1]
Signed-off-by: Eric Lin <eric.lin@sifive.com>
Reviewed-By: Xiang W <wxjstz@126.com>
Reviewed-By: Anup Patel <anup@brainfault.org>
The console device is registered by platform only in early_init()
callback so any prints before this point will be lost. Introduce an
early console buffer for caching prints before platform early_init().
For crashes before platform early_init(), users can simply dump the
contents of the console_early_buffer[] string using a debugger. The
relative address of the console_early_buffer[] string can be found
using following two commands:
CONSOLE_EARLY_FIFO_ADDR=`${CROSS_COMPILE}objdump -D \
build/platform/generic/firmware/fw_dynamic.elf | \
grep "<console_early_fifo>:" | awk '{print $1}'`
${CROSS_COMPILE}objdump -R build/platform/generic/firmware/fw_dynamic.elf | \
grep $CONSOLE_EARLY_FIFO_ADDR | awk '{print $3}'
Signed-off-by: Anup Patel <apatel@ventanamicro.com>
Reviewed-By: Himanshu Chauhan <hchauhan@ventanamicro.com>
The FIFO data structure is quite handy of variety of use-case so add
SBI_FIFO_INITIALIZER() and SBI_FIFO_DEFINE() helper macros to create
FIFO as local or global variable.
Signed-off-by: Anup Patel <apatel@ventanamicro.com>
Reviewed-By: Himanshu Chauhan <hchauhan@ventanamicro.com>
Extend sbi_fifo_enqueue() to allow forceful queueing by droping
data from the tail.
Signed-off-by: Anup Patel <apatel@ventanamicro.com>
Reviewed-By: Himanshu Chauhan <hchauhan@ventanamicro.com>
Don't use sbi_memcpy() for basic data types in fifo enqueue/dequeue
instead use direct type-cast and assignment.
Signed-off-by: Anup Patel <apatel@ventanamicro.com>
Reviewed-By: Himanshu Chauhan <hchauhan@ventanamicro.com>
Now that all platforms have been updated to initialize serial console
device in early_init(), the sbi_console_init() and console_init()
platform callback are redundant hence remove them.
Signed-off-by: Anup Patel <apatel@ventanamicro.com>
Reviewed-By: Himanshu Chauhan <hchauhan@ventanamicro.com>
The sbi_console_init() does not do any special initialization so
setup serial console device in early_init() so that console prints
work as early as possible.
Signed-off-by: Anup Patel <apatel@ventanamicro.com>
Reviewed-By: Himanshu Chauhan <hchauhan@ventanamicro.com>
Attempting to access the menvcfg CSR raises an illegal instruction
exception on hardware which implements Sm1p11 or older.
Fixes: e9ee9678ba ("lib: sbi: fwft: add support for SBI_FWFT_PTE_AD_HW_UPDATING")
Signed-off-by: Samuel Holland <samuel.holland@sifive.com>
Reviewed-by: Anup Patel <anup@brainfault.org>
A new property has been added, with an extensive rationale at [1], that
can be used in place of "riscv,isa" to indicate what extensions are
supported by a given platform that is a list of strings rather than a
single string. There are some differences between the new property,
"riscv,isa-extensions" and the incumbent "riscv,isa" - chief among them
for the sake of parsing being the list of strings, as opposed to a
string. Another advantage is strictly defined meanings for each string
in a dt-binding, rather than deriving meaning from RVI standards. This
may likely to some divergence over time, but, at least for now, there's
no relevant differences between the two for an M-Mode program.
Add support for the new property in OpenSBI, prioritising it, before
falling back to the, now deprecated, "riscv,isa" property if it is not
present.
Link: https://lore.kernel.org/all/20230702-eats-scorebook-c951f170d29f@spud/ [1]
Signed-off-by: Conor Dooley <conor.dooley@microchip.com>
Reviewed-by: Anup Patel <anup@brainfault.org>
This patch introduces a new math test suite to the SBI unit
tests. The changes include:
* Updating lib/sbi/tests/objects.mk to include
math_test_suite and sbi_math_test.o.
* Adding a new file lib/sbi/tests/sbi_math_test.c which
contains tests for log2roundup function using various cases.
The addition of this test suite ensures that mathematical
functions are verified and work as expected.
Signed-off-by: Dongdong Zhang <zhangdongdong@eswincomputing.com>
Reviewed-by: Anup Patel <anup@brainfault.org>
This patch improves the readability of the SBI unit test
output by adding color-coded status messages.
Adding ANSI color codes for green (pass) and red (fail)
in sbi_unit_test.c.
Now, the test results will be displayed in green for passed
tests and red for failed tests, making it easier to quickly
distinguish between them.
Signed-off-by: Dongdong Zhang <zhangdongdong@eswincomputing.com>
Reviewed-by: Anup Patel <anup@brainfault.org>
After the changes introduced by the previous patches are applied, there
is no need of the manual removal of the `build/` directory every time
new test is added. Running `make clean` should be enough to regenerate
the carray-related files.
Update the documentation correspondingly.
Signed-off-by: Ivan Orlov <ivan.orlov0322@gmail.com>
Reviewed-by: Andrew Jones <ajones@ventanamicro.com>
Signed-off-by: Ben Dooks <ben.dooks@codethink.co.uk>
Reviewed-by: Anup Patel <anup@brainfault.org>
Now we've renamed the carray output files to .carray.c
we can now use find to remove them.
Signed-off-by: Ben Dooks <ben.dooks@codethink.co.uk>
Reviewed-by: Andrew Jones <ajones@ventanamicro.com>
Reviewed-by: Anup Patel <anup@brainfault.org>
We would like to clean any files generated by the carray
scripts by just searching for the filename as the current
make system turns f.carray into f.o. Change to make the
make system turn f.carray into f.carray.o
note, command to go through .mk files changing the .o
in the .mk files is:
find . -type f -name "*.carray" | xargs -t -I fname /bin/bash -x -c ' fn=`basename -s .carray fname`; echo "$fn"; sed -i `dirname fname `/objects.mk -e s/"$fn".o/"$fn".carray.o/g'
Link: https://patchwork.ozlabs.org/project/opensbi/patch/20240401213438.590209-2-ivan.orlov0322@gmail.com/
Reported-by: Ivan Orlov <ivan.orlov0322@gmail.com>
Suggested-by: Andrew Jones <ajones@ventanamicro.com>
Signed-off-by: Ben Dooks <ben.dooks@codethink.co.uk>
Reviewed-by: Andrew Jones <ajones@ventanamicro.com>
Reviewed-by: Anup Patel <anup@brainfault.org>
Add a comment about where auto-generated file came from to the carray.sh
output. This should help avoiding confusion for the developers looking
at the build artifacts and finding .c files there.
Signed-off-by: Ivan Orlov <ivan.orlov0322@gmail.com>
Reviewed-by: Andrew Jones <ajones@ventanamicro.com>
Signed-off-by: Ben Dooks <ben.dooks@codethink.co.uk>
Reviewed-by: Anup Patel <anup@brainfault.org>
Illegal CSR accesses from lower privilege modes are delegated to S-mode
and do not necessarily indicate a bug. Supervisor software may want to
emulate some CSRs, or may intentionally disable access to certain
existing CSRs, and thus will expect traps when those CSRs are accessed.
For example, Linux disables sstatus.VS by default in order to detect
when userspace first accesses vector register state; this includes the
CSRs defined by the V extesion. As a result, if the first vector
instruction in a process is a CSR access, OpenSBI will log the illegal
instruction exception, even though there is no unexpected or erroneous
behavior occurring.
Since the illegal instruction exception is delegated to S-mode, S-mode
software should be responsible for reporting the exception, not OpenSBI.
Signed-off-by: Samuel Holland <samuel.holland@sifive.com>
Reviewed-by: Anup Patel <anup@brainfault.org>
This commit adds a new GitHub Actions workflow for repository
lockdown. The workflow triggers when a pull request is opened, and it
notifies the contributor to use the OpenSBI mailing list for patch
reviews.
Additionally, the .gitignore file is updated to include the .github
directory.
Signed-off-by: Dongdong Zhang <zhangdongdong@eswincomputing.com>
Reviewed-by: Anup Patel <anup@branifault.org>
This patch updates OpenSBI version to 1.5 as part of
release preparation.
Signed-off-by: Anup Patel <apatel@ventanamicro.com>
Signed-off-by: Anup Patel <anup@brainfault.org>
Current Debug Trigger SBI extension proposal suggests to activate
shmem area and obtain its physical address from S-mode software
in the following way:
: If both `shmem_phys_lo` and `shmem_phys_hi` parameters are not
: all-ones bitwise then `shmem_phys_lo` specifies the lower XLEN
: bits and `shmem_phys_hi` specifies the upper XLEN bits of the
: shared memory physical base address. The `shmem_phys_lo` MUST
: be `(XLEN / 8)` byte aligned and the size of shared memory is
: assumed to be `trig_max * (XLEN / 2)` bytes.
For more details see the current version of the proposal:
- https://lists.riscv.org/g/tech-debug/message/1302
On the other hand, on RV32, the M-mode can only access the first 4GB of
the physical address space because M-mode does not have MMU to access
full 34-bit physical address space. Similarly, on RV64, the M-mode can
only access memory addressed by 64 bits.
This commit checks shmem address in function sbi_dbtr_setup_shmem
to make sure that shmem_phys_hi part of the valid address is zero.
Besides, the macro DBTR_SHMEM_MAKE_PHYS is updated to take into
account only low XLEN part.
Signed-off-by: Sergey Matyukevich <geomatsi@gmail.com>
Reviewed-by: Himanshu Chauhan <hchauhan@ventanamicro.com>
Correct the compiled FW_PAYLOAD firmware ELF filename.
Signed-off-by: Jacob Lin <lovetaeyeon507@gmail.com>
Reviewed-by: Anup Patel <anup@brainfault.org>
Error code returned by the ecall handles should use the defines from
sbi_ecall_interface.h rather than sbi_error.h.
Signed-off-by: Clément Léger <cleger@rivosinc.com>
Reviewed-by: Andrew Jones <ajones@ventanamicro.com>
Reviewed-by: Anup Patel <anup@brainfault.org>
As stated by the spec and pointed out by Andrew Jones, the value passed
for MISALIGNED_EXC_DELEG and PTE_AD_HW_UPDATING should be either 0 or 1.
Add check for these values and return SBI_EINVAL if not.
Signed-off-by: Clément Léger <cleger@rivosinc.com>
Reviewed-by: Andrew Jones <ajones@ventanamicro.com>
Reviewed-by: Anup Patel <anup@brainfault.org>
The SBI FWFT extension defines a set of function that can be called
to control the configuration of some platform features (misaligned
trap delegation, etc). This patch implements sbi_fwft_set() and
sbi_fwft_get() as defined in the specification [1].
Link: https://lists.riscv.org/g/tech-prs/message/924 [1]
Signed-off-by: Clément Léger <cleger@rivosinc.com>
Reviewed-by: Anup Patel <anup@brainfault.org>
Add support for SBI_FWFT_PTE_AD_HW_UPDATING based on SVADU presence.
Signed-off-by: Clément Léger <cleger@rivosinc.com>
Reviewed-by: Anup Patel <anup@brainfault.org>
Add support for SBI_FWFT_MISALIGNED_EXC_DELEG withing FWFT support. This
support allows to delegate misaligned accesses traps.
Signed-off-by: Clément Léger <cleger@rivosinc.com>
Reviewed-by: Anup Patel <anup@brainfault.org>
This extension allows the software running in supervisor mode to control
the behavior of various features of the SBI [1]. Implement the support
for such extension.
Link: https://lists.riscv.org/g/tech-prs/message/924 [1]
Signed-off-by: Clément Léger <cleger@rivosinc.com>
Reviewed-by: Anup Patel <anup@brainfault.org>
Add support for Svade and Svadu extensions. When both are present in the
device tree, the M-mode firmware should select the Svade extension
to comply with the RVA23 profile, which mandates Svade and lists Svadu as
an optional extension.
Signed-off-by: Yong-Xuan Wang <yongxuan.wang@sifive.com>
Reviewed-by: Anup Patel <anup@brainfault.org>
Like PMP, the behaviors to configure PMA will be different from
RV64 and RV32. RV64 uses two Andes custom CSRs, pmacfg0 and pmacfg2,
but RV32 uses four Andes custom CSRs, pmacfg0 ~ pmacfg3. This patch
adds support to PMA for RV32.
Signed-off-by: Ben Zong-You Xie <ben717@andestech.com>
Reviewed-by: Anup Patel <anup@brainfault.org>
This patch refines the Andes PMA related code. The main change is
refactor andes_pma_[read|write]_cfg() and andes_pma_[read|write]_addr()
into new functions andes_pma_[read|write]_num().
Also, fix some coding style problems.
Signed-off-by: Ben Zong-You Xie <ben717@andestech.com>
Reviewed-by: Anup Patel <anup@brainfault.org>
When used to read characters from the terminal (e.g., when the SBI
console is used via ecall from linux with `console=hvc0`), we must
acknowledge receipt of each character to "pop" it off the LiteUART
hardware queue, and allow the next character to be made available.
Fixes: 52af6e4b ("lib: utils: Add LiteX UART support")
Suggested-by: Dolu1990 <charles.papon.90@gmail.com>
Signed-off-by: Gabriel Somlo <gsomlo@gmail.com>
Reviewed-by: Anup Patel <anup@brainfault.org>
In DT, multiple reset devices may use the same driver, and they
may have different priorities. If rc is returned after the first
initialization, the highest priority device may be lost.
Fixes: a73ff043e9 (lib: utils/reset: Fix fdt_reset to search for more dt nodes)
Signed-off-by: Xiang W <wxjstz@126.com>
Reviewed-by: Anup Patel <anup@brainfault.org>
If there are multiple dt nodes, the previous code only tries to match
the first one, which may lose initialization.
Signed-off-by: Xiang W <wxjstz@126.com>
Reviewed-by: Anup Patel <anup@brainfault.org>
When the dt node has a status property and the value is not ok or
okay, skip initializing reset.
Signed-off-by: Xiang W <wxjstz@126.com>
Reviewed-by: Anup Patel <anup@brainfault.org>
If there are multiple dt nodes, the previous code only tries to match
the first one, which may lose initialization.
Signed-off-by: Xiang W <wxjstz@126.com>
Reviewed-by: Anup Patel <anup@brainfault.org>
When the dt node has a status property and the value is not ok or
okay, skip initializing serial.
Signed-off-by: Xiang W <wxjstz@126.com>
Reviewed-by: Anup Patel <anup@brainfault.org>
When the dt node has a status property and the value is not ok or
okay, skip initializing irqchip.
Signed-off-by: Xiang W <wxjstz@126.com>
Reviewed-by: Anup Patel <anup@brainfault.org>
When the dt node has a status property and the value is not ok or
okay, skip initializing timer.
Signed-off-by: Xiang W <wxjstz@126.com>
Reviewed-by: Anup Patel <anup@brainfault.org>
When the dt node has a status property and the value is not ok or
okay, skip initializing ipi.
Signed-off-by: Xiang W <wxjstz@126.com>
Reviewed-by: Anup Patel <anup@brainfault.org>
During Linux AIA driver review, the APLIC DT property for interrupt
delegation was renamed to "riscv,delegation" so let's use the new DT
property name and fallback to old DT property name if the new DT
property name is not available.
Fixes: 34612193af ("lib: utils/irqchip: Add FDT based driver for APLIC")
Signed-off-by: Anup Patel <apatel@ventanamicro.com>
"gpio-poweroff" and "gpio-restart" always set gpio to high to
active the function, but some chips need a low signal to active.
Fortunately, it can be achieved by setting GPIO_FLAG_ACTIVE_LOW
for the gpio. Implement this flag support for the gpio library
so the gpio reset can function well.
Signed-off-by: Inochi Amaoto <inochiama@outlook.com>
Reviewed-by: Anup Patel <anup@brainfault.org>
The spec states that a6, a7, flags and sepc are writable but the
implementation was not allowing that. Add support for these 4 writable
attributes.
Signed-off-by: Clément Léger <cleger@rivosinc.com>
Reviewed-by: Samuel Holland <samuel.holland@sifive.com>
Reviewed-by: Anup Patel <anup@brainfault.org>
Add extra sanity checks to prevent the caller getting the invalid result from
imsic_get_data() or imsic_get_target_file() when imsic is not initialized
correctly.
Signed-off-by: Cyan Yang <cyan.yang@sifive.com>
Reviewed-by: Anup Patel <anup@brainfault.org>
Bring back FW_TEXT_START as an optional parameter to allow users
explicitly specify compile time address for loading debug symbols.
When not specified, the FW_TEXT_START is assumed to be 0.
Fixes: d4d2582eef ("firmware: remove FW_TEXT_START")
Signed-off-by: Anup Patel <apatel@ventanamicro.com>
Tested-by: Clément Léger <cleger@rivosinc.com>
The current mlevel imsic check is only for the platform, which
may cause hart without imsic in the platform to trigger an
illegal instruction exception when initializing imsic. For
example, the platform contains a management hart that only
supports wired interrupts.
This patch will check if each hart supports Smaia extension
before doing imsic initialization to avoid triggering illegal
instruction exceptions.
Signed-off-by: Cheng Yang <yangcheng.work@foxmail.com>
Reviewed-by: Anup Patel <anup@brainfault.org>
The Sophgo CV18XX/SG200X series SoCs have a standard C906
core. Add support for it.
Signed-off-by: Inochi Amaoto <inochiama@outlook.com>
Reviewed-by: Anup Patel <anup@brainfault.org>
Currently, the sbi_sse_exit() gets event in a loop but does not put
it back after use. This results in global events remaining locked
causing hangs on sub-sequent calls to sse_event_get() for global
events.
Fixes: c8cdf01d8f ("lib: sbi: Add support for Supervisor Software Events extension")
Signed-off-by: Anup Patel <apatel@ventanamicro.com>
Reviewed-by: Himanshu Chauhan <hchauhan@ventanamicro.com>
SG2042 uses an onboard MCU to provide reset function.
Add reset driver to support this onboard MCU.
Signed-off-by: Inochi Amaoto <inochiama@outlook.com>
Reviewed-by: Anup Patel <anup@brainfault.org>
The inline function can simplify the code by setting some call
restrictions. This ensures logical smoothness
Signed-off-by: Xiang W <wxjstz@126.com>
Reviewed-by: Anup Patel <anup@brainfault.org>
Modify the return value of the sbi_dbtr_shmem_disabled function to
bool to make the semantics clearer.
Signed-off-by: Xiang W <wxjstz@126.com>
Reviewed-by: Anup Patel <anup@brainfault.org>
Eric Lin